Phaser® 560 Color Laser Printer Warranty Tektronix warrants that the Phaser 560 Color Laser Printer will be free from defects in materials and workmanship for a period of one (1) year from the date of shipment and that Customer-Replaceable Components (CRCs)* in this product will be free from defects in materials and workmanship for a period of ninety (90) days from the date of shipment or six months where longer periods are required by law. If the product or its CRCs prove defective during their respective warranty periods, Tektronix, at its option, will either repair the defective product or CRC without charge for parts and labor, or provide a replacement in exchange for the defective product or CRC. The 90-day warranty applies only to CRCs returned to the designated Tektronix depot or the Tektronix authorized representative from which the CRC was originally purchased. For CRCs returned to other locations, Customer will be assessed an applicable service charge. The preceding limitation shall not apply within the European Economic Area, where CRCs may be returned for warranty service to the nearest designated service depot regardless of the place of purchase. In order to obtain service under the 90-day CRC warranty, Customer must provide the applicable office of Tektronix or its authorized representative with notice of the defect before the expiration of the warranty period and make suitable arrangements for the performance of service. Customer shall be responsible for packaging and shipping the defective CRC to the service center designated by Tektronix or its representative, with shipping charges prepaid. Tektronix or its representative shall pay for the return of the CRC to Customer. Customer shall be responsible for paying any associated taxes or duties. In order to obtain service under the one-year on-site product warranty, Customer must notify Tektronix or its authorized representative of the defect before the expiration of the warranty period and make suitable arrangements for the performance of service. Tektronix or its authorized representative will provide such service at the Customer's site without charge during the warranty period, if the service is performed within the United States or outside the United States if the product is located in a normal on-site service area. Outside the U.S., a description of the normal on-site service area can be obtained from the Local Tektronix Subsidiary or Authorized Tektronix Distributor. This warranty shall not apply to any defect, failure or damage caused by improper use or improper or inadequate maintenance and care. Tektronix shall not be obligated to furnish service under this warranty: a) to repair damage resulting from attempts by personnel other than Tektronix representatives to install, repair or service the product or CRC; b) to repair damage resulting from improper use or connection to incompatible equipment; c) to repair any damage or malfunction caused by the use of non-Tektronix supplies or consumables; d) to repair a product or CRC that has been modified or integrated with other products when the effect of such modification or integration increases the time or difficulty of servicing the product or CRC; e) to repair damage or malfunction resulting from failure to perform user maintenance and cleaning at the frequency and as prescribed in the user manual; or f) to repair this product after the limit of its duty cycle of 20,000 pages per month has been reached; all service thereafter shall be billed on a time-and-material basis. g) to repair or replace CRCs that have been used beyond their stated capacities. the above warranties are given by tektronix with respect to this product and its customer-replaceable components in lieu of any other warranties, express or implied. tektronix and its vendors disclaim any implied warranties of merchantability or fitness for a particular purpose. tektronix' responsibility to repair or replace defective products and customer-replaceable components is the sole and exclusive remedy provided to the customer for breach of this warranty. tektronix and its vendors will not be liable for any indirect, special, incidental, or consequential damages irrespective of whether tektronix or the vendor has advance notice of the possibility of such damages. * Customer-Replaceable Components in this product are specifically: fuser, fuser roll, imaging unit, transfer kit (transfer roller and waste bin) and toner cartridges. User safety summary Terms in manual: CAUTION Conditions that can result in damage to the product. WARNING Conditions that can result in personal injury or loss of life. Power source: Do not apply more than 250 volts RMS between the supply conductors or between either supply conductor or ground. Use only the specified power cord and connector. Refer to a qualified service technician for changes to the cord or connector. Operation of product: Avoid electric shock by contacting a qualified service technician to replace fuses inside the product. Do not operate without the covers and panels properly installed. Do not operate in an atmosphere of explosive gases. Safety instructions: Read all installation instructions carefully before you plug the product into a power source. Terms on product: CAUTION A personal injury hazard exists that may not be apparent. For example, a panel may cover the hazardous area. Also applies to a hazard to property including the product itself. DANGER A personal injury hazard exists in the area where you see the sign. Care of product: Disconnect the power plug by pulling the plug, not the cord. Disconnect the power plug if the power cord or plug is frayed or otherwise damaged, if you spill anything into the case, if product is exposed to any excess moisture, if product is dropped or damaged, if you suspect that the product needs servicing or repair, and whenever you clean the product. Ground the product: Plug the three-wire power cord (with grounding prong) into grounded AC outlets only. If necessary, contact a licensed electrician to install a properly grounded outlet. Symbols as marked on product: DANGER high voltage: Protective ground (earth) terminal: Use caution. Refer to the manual(s) for information: WARNING: If the product loses the ground connection, usage of knobs and controls (and other conductive parts) can cause an electrical shock. Electrical product may be hazardous if misused. This product is certified under IEC 825 as a Class 1 Laser Product: WARNING: For your protection, do not defeat any interlocks. CAUTION: This product utilizes a laser. Use of control or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Do not open covers and do not repair yourself. Refer servicing to qualified personnel. When you operate this equipment, the socket outlet should be near the equipment and be easily accessible.
FOR USERS IN NORWAY VARNING! OM APPARATEN ANVANDS PÅ ANNAT SÄTT Än i denna bruksanvisning speCIFicERATS, KAN ANVÄNDAREN UTSÄTTAS FOR OSYNLIG LASERSTRÅLING, SOM ÖVERSKRIDER GRÄNSEN FOR LASERKLASS 1. Apparaten skall anslutas till jordat uttag när den ansluts till ett Nätverk.
FOR USERS IN JAPAN This equipment is in the 2nd Class category (information equipment to be used in a residential area or an adjacent area thereto) and conforms to the standards set by the Voluntary Control Council For Interference by Information Technology Equipment aimed at preventing radio interference in such residential area. When used near a radio or TV receiver, it may become the cause of radio interference. Read the instructions for correct handling.
