Changes to Xerox parts are made to accommodate improved
components as they become available. It is important when ordering
parts to include the following information:
- Component's part number.
- Instrument type or number.
- Instrument serial number.
- Modification number, if any.
Using the Parts List
- The numbers shown in each illustration correspond to the parts
list number for that illustration.
- The capital letters “C”, “E”, and “S” shown
in an illustration stand for C-ring, E-ring, and Screw, respectively.
- A shaded triangle t in an illustration indicates the item is
part of an assembly.
- The notation “with X~Y” following an part name
indicates an assembly that is made up of components X through
Y. For example, “1 (with 2~4)” means part 1 consists
of part 2, part 3, and part 4.
- An asterisk * following a part name indicates the page contains
a note about this part.
- A notation “(part of item 1.1)” indicates that
the part is included with item 1.2.1 (PL1.2, line item 1).
|
PL 1.0 - Cabinet and
Top Cover FRU's
| Fig 1 Parts
| Part number
| Name and description
|
| 1
| 116-0998-00
| Top Cover/Face Down Stack Bin
|
| 2
| 116-1083-00
| Side Output Tray/Face Up Stack Tray
|
| 3
| 116-1061-00
| Side Output Tray Link
|
| 4
| 116-1052-00
| Top Cover Hinge Spring - Rear
|
| 5
| 116-1053-00
| Top Cover Hinge Shaft
|
| 6
| 116-1051-00
| Top Cover Hinge Spring - Front
|
| 7
| 116-1006-00
| Left Side Cover
|
| 8
| 116-1004-00
| Front Cover
|
| 9
| 116-1039-00
| Duplex Slot Cover
|
| 10
| 116-1055-00
| Top Cover Damper - Front
|
| 12 |
116-1008-00
|
Foot |
| 13
| 116-1084-00
| Right Side Door |
| 14
| 012E12690 |
Multi-Sheet Bypass Links (Front & Rear) |
| 15
| 116-1017-00
| Multi-Sheet Bypass Tray |
| 17 |
|
Multi-Sheet Bypass Drive Gear (part of 116-1037-00 Gear Kit) |
| 18 |
116-1025-00 |
Top Cover Interlock Switch |
| 19 |
116-1016-00 |
Multi-Sheet Bypass Pick Assembly |
| 20 |
116-1018-00 |
Multi-Sheet Bypass Feeder Top Cover |
| 21 |
116-1056-00 |
Top Cover Damper - Rear |
| 22 |
116-1059-00 |
Top Cable Shield |
| 23 |
116-1005-00 |
Rear Cover |
| 24 |
|
Temperature/Humidity Sensor Board |
PL 2.0 - Top Cover
Inner Frame
| Fig 2 Parts |
Part Number |
Name and description |
| 1 |
|
Exit/Stack Full Sensor Actuator (part of 116-1036-00
Flag Kit) |
| 2 |
116-1000-00 |
Exit/Stack Full Sensor |
| 3 |
116-1054-00 |
Top Output (Face-down) Eject Sensor Assembly |
| 4 |
116-1082-00 |
Control Panel Bezel |
| 5 |
116-1003-00 |
Control Panel Assembly |
| 6 |
|
Control Panel Tape Harness (part of 116-1035-00 Harness
Kit) |
| 7 |
|
Idler Rollers/Face Up Side Tray (part of 116-1038-00
Hardware Kit) |
| 8 |
116-1057-00 |
Top Cover/Stack Bin - Inner Cover |
| 9 |
116-1002-00 |
Eject Guide Assembly |
| 10 |
116-0999-00 |
LED Bar Assembly |
| 11 |
|
LED Assembly Spring (part of 116-1038-00 Hardware Kit) |
| 12 |
|
26-pin LED Connector (part of 116-1035-00 Harness Kit) |
| 13 |
|
Black LED Wiring Harness (part of 116-1035-00 Harness
Kit) |
| 14 |
|
Yellow LED Wiring Harness (part of 116-1035-00 Harness
Kit) |
| 15 |
|
Magenta LED Wiring Harness (part of 116-1035-00 Harness
Kit) |
| 16 |
|
Cyan LED Wiring Harness (part of 116-1035-00 Harness
Kit) |
| 17 |
116-1001-00 |
Top Cover Inner Frame |
| 18 |
116-1024-00 |
Fuser Fan |
| 19 |
|
Toner Cartridge Sensor Actuator (part of 116-1036-00
Flag Kit) |
| 20 |
116-1321-00 |
LED/Toner Control Board |
PL 3.0 - Printer Chassis (1
of 2)
| Fig 3 parts |
Part number |
Name and description |
| 1 |
116-1022-00 |
Fuser Exit Roller |
| 2 |
116-1019-00 |
Duplex Guide Assembly |
| 3 |
|
Fuser Latch Handle Spring (part of 116-1038-00
Hardware Kit) |
| 4 |
003E55690 |
Fuser Latching Handle (Front) |
| 5 |
130K65670 |
Fuser Exit Sensor Assembly |
| 6 |
116-1021-00 |
Top/Side Output Solenoid Assembly |
| 7 |
|
Fuser Exit Roller Bushing (Front) (part
of 116-1038-00 Hardware Kit) |
| 8 |
116-1020-00 |
Duplex Gate Solenoid Assembly |
| 9 |
116-1066-00 |
Front Power Supply Fan |
| 10 |
116-1032-00 |
Color Registration Sensor Assembly |
| 11 |
116-1030-00 |
Color Registration Plate Shutter |
| 12 |
|
Registration Shutter Spring (part of 116-1038-00
Hardware Kit) |
| 13 |
121K26000 |
Color Registration Shutter Solenoid |
| 14 |
116-1087-00 |
Printer Chassis |
| 15 |
|
B Registration Entrance Sensor Flag (part
of 116-1036-00 Flag Kit) |
| 16 |
116-1015-00 |
Registration Roller Assembly (B) |
| 17 |
600K88480 |
Entrance Sensor Board |
| 18 |
|
A Registration Exit Sensor Actuator (Belt
Entrance) |
| |
|
(part of 116-1036-00 Flag Kit) |
| 19 |
|
A Registration Entrance Sensor Actuator
(part of 116-1036-00 Flag Kit) |
| 20 |
121K25810 |
Registration Clutch |
| 21 |
116-1012-00 |
Registration Motor Assembly |
| 22 |
|
Registration Drive Gear A (part of 116-1037-00
Gear Kit) |
| 23 |
116-1014-00 |
Registration Roller Assembly (A) |
| 24 |
115K01970 |
Drum Contact Assembly |
| 25 |
116-1068-00 |
Transfer Contact Assembly |
| 26 |
|
Fuser Exit Roller Bushing (Back) (part
of 116-1038-00 Hardware Kit) |
| 27 |
116-1028-00 |
Rear Power Supply Fan |
PL 4.0 - Printer Chassis
(2 of 2)
| Fig 4 parts |
Part number |
Name and description |
| 1 |
003E55700 |
Fuser Latching Handle (Rear) |
| 2 |
116-1011-00 |
Transfer Belt Motor Assembly |
| 3 |
116-1026-00
116-1027-00 |
Low Voltage Power Supply (115 VAC)
Low Voltage Power Supply (220 VAC) |
| 4 |
116-1029-00 |
Front Plate Assembly |
| 5 |
116-1034-00 |
Low Voltage Power Supply Insulator |
| 6 |
116-1067-00 |
Duplex Exit Paper Guide |
| 7 |
115K01960 |
Rear Contact Assembly |
| 8 |
116-1033-00 |
High Voltage Power Supply Insulator |
| 9 |
105K25120 |
High Voltage Power Supply |
| 10 |
|
High Voltage Tape Harness (part of 116-1035-00 Harness
Kit) |
| 11 |
116-1063-00 |
Back Plate Assembly w/ Imaging Drum Drive Gears |
| 12 |
116-1064-00 |
Imaging Drum Motor |
| 13 |
116-1215-00 |
Chassis fan |
PL 5.0 - Paper Tray
and Paper Tray Guides
| Fig 5 Parts |
Part Number |
Name and description |
| 1 |
116-1009-00 |
Universal Paper Tray |
| 2 |
116-1085-00 |
Connector with Harness |
| 3 |
116-1065-00 |
Right Cover Interlock Switch |
| 4 |
116-1086-00
116-1643-00 |
Main Feeder Assembly
Jam Access Shutter w/Return Spring |
| 5 |
116-1062-00 |
Paper Feed Roller |
| 6 |
116-1010-00 |
Feed Motor |
| 7 |
116-1007-00 |
Paper Size Sensing Board (includes Ribbon
Harness) |
| 8 |
116-1216-00 |
Roller Clutches (Bearing, One-Way) |
| 9 |
116-1214-00 |
Roller Torque Limiter |
PL 6.0 - Electrical
Components FRU's
| Fig 6 Parts |
Part Number |
Name and description |
| 1 |
116-1050-00 |
Electrical Card Change |
| 2 |
116-1023-00 |
Electrical Chassis Cooling Fan |
| 3 |
537E61970 |
CRU EEPROM 816A2323M000 |
| 4 |
116-1031-00 |
Engine Controller Board |
| 5 |
671-5269-00 |
System Controller Board (EFI Controller),
Image Processor |
| 6 |
156-4811-10
156-4780-10
156-4839-00
|
64-Mbyte RAM DIMM
128-Mbyte RAM DIMM
256-Mbyte RAM DIMM |
| 7 |
650-4209-00 |
Internal IDE Hard Drive, Programmed |
| 8 |
160-1060-00 |
Outer (Rear) Shield Plate |
| 9 |
674-5282-00 |
Code ROM DIMM |
PL 7.0 - Duplexer
Unit FRU's
| Fig 7 Parts |
Part Number |
Name and description |
| 1 |
650-4230-00 |
Duplex Transport Assembly |
PL 8.0 - Lower Tray
Assembly FRU's
| Fig 10 Parts |
Part Number |
Name and description |
| |
119-6376-00 |
Lower Tray Assembly (with tray) |
| |
119-6377-00 |
Lower Tray Deck (with trays) |
| 1 |
116-1045-00 |
Lower Tray Assembly Left Cover |
| 2 |
116-1043-00 |
Lower Tray Assembly Front Right Cover |
| 3 |
116-1042-00 |
Lower Tray Assembly Universal Tray |
| 4 |
116-1013-00 |
Castor Wheel |
| 5 |
116-1046-00 |
Lower Tray Assembly Right Side Cover (Door) |
| 6 |
116-1047-00 |
Lower Tray Assembly Main Feeder Assembly |
| 7 |
116-1048-00 |
Lower Tray Assembly Control Board |
| 8 |
116-1044-00 |
Lower Tray Assembly Rear Cover |
| 9 |
116-1040-00 |
Lower Tray Assembly Top Connector |
Kits
| Part number
| Name / Parts Included
|
| 116-1038-01
| Hardware
Kit
|
| LED Assembly Spring Kit
|
| Fuser Exit Roller Bushing (Front)
|
| Fuser Exit Roller Bushing (Back)
|
| Registration Shutter Spring
|
| Fuser Latch Handle Springs
|
| Screw (T3x8)
|
| Screw (T3x10)
|
| Screw (T4x10)
|
| Screw (M2x8)
|
| Screw (M3x6)
|
| Screw (M3x8)
|
| Screw (M4x8)
|
| Screw (SP3x10)
|
| Screw (T4X6)
|
| Screw (T4X8)
|
| Plastic Eject Rollers
|
| Part
number
| Name / Parts Included
|
| 116-1037-00
| Gear Kit
|
| Main Feeder Drive Gear
|
| Fuser Drive Gear A
|
| Fuser Drive Gear B
|
| Fuser Drive Gear C
|
| Registration Drive Gear A
|
| Multi-Purpose Tray Drive Gear
|
| Imaging Unit Drive Gear
|
| Part
number
| Name / Parts Included
|
| 116-1035-00
| Harness Kit
|
| LED Harness M
|
| LED Harness C
|
| LED Harness Y
|
| LED Harness K
|
| 26 pin LED connector
|
| Control Panel Tape Harness
|
| High Voltage Tape Harness
|
| For Heat Motor, Belt Motor
|
| For MBF paper End sensor, Near End sensor, OHP sensor
|
| For 1stPaperEnd sensor, Near end sensor, 2nd Interface,
Temp/Humidity sensor
|
| For Geared Motor
|
| For Feed sensor
|
| For Color Registration sensor
|
| For Board N71
|
| For Board R71
|
| For Board A73
|
| For Duplexer
|
| For Power
|
| For Right side Cover Open, Stacker Cover Open
|
| For Right side Cover Open-Relay cable
|
| For C73 Interface (Finisher)
|
| For Job Offset motor, Fuser Fan-relay cable
|
| For Image Drum Motor
|
| For hopping Motor, MBF/Registration Motor
|
| For pickup clutch, feed roller Clutch
|
| Temp/Humidity sensor-relay cable
|
| Paper End sensor-relay, Paper Near End sensor-relay
cable
|
| For Paper Size Detect (board B73)
|
| For Y71 PWB
|
| Part
number
| Name / Parts Included
|
| 116-1036-00
| Flag Kit
|
| Stack Full Flag
|
| Toner Sensor Actuator (qty of 4)
|
| Intermediate Exit Flag
|
| B Reg Entrance Sensor Flag
|
| A Reg Entrance Sensor Flag
|
| A Reg Exit Sensor Flag
|
| Tray 1 Media Low Flag
|
| Tray 1 Media Out Flag
|
Supplies
and Accessories
| Part number
| Name / Parts Included
|
| 016-1927-00
| Transfer Belt
|
| Fuser:
|
016-1925-00
016-1926-00
| 110 Volt
220 Volt
|
| Imaging Drum Units:
|
| 016-1921-00
| Black Imaging Drum
|
| 016-1922-00
| Cyan Imaging Drum
|
| 016-1923-00
| Magenta Imaging Drum
|
| 016-1924-00
| Yellow Imaging Drum
|
| Standard Capacity Toner Cartridges:
|
| 016-1913-00
| Black
|
| 016-1914-00
| Cyan
|
| 016-1915-00
| Magenta
|
| 016-1916-00
| Yellow
|
| High Capacity Toner Cartridges:
|
| 016-1917-00
| Black
|
| 016-1918-00
| Cyan
|
| 016-1919-00
| Magenta
|
| 016-1920-00
| Yellow
|
| 016-1927-00
| Black
|
| Manuals:
|
| 061-4288-00
| Phaser 2135 Manual Pack (English)
|
| 061-4289-00
| Phaser 2135 Manual Pack (French)
|
| 061-4290-00
| Phaser 2135 Manual Pack (Italian)
|
| 061-4291-00
| Phaser 2135 Manual Pack (German)
|
| 061-4292-00
| Phaser 2135 Manual Pack (Spanish)
|
| 061-4293-00
| Phaser 2135 Manual Pack, Brazilian/Portuguese
|
| 061-4294-00
| Phaser 2135 Manual Pack, Simplified Chinese
|
| 061-4295-00
| Phaser 2135 Manual Pack, Traditional Chinese
|
| 061-4296-00
| Phaser 2135 Manual Pack, Korean
|
| 061-4298-00
| Phaser 2135 Manual Pack, Dutch
|
| 061-4299-00
| Phaser 2135 Manual Pack, Swedish
|
| 071-0725-00
| Phaser 2135 Service Quick Reference Guide
|
| 063-3399-00
| CD-ROM, Printer Software, Drivers and Utilities
|
| 063-3400-00
| CD-ROM, Printer Management
|
| 003-1496-00
| Toner Vacuum (115 VAC)
|
| 003-1497-00
| Toner Vacuum (220 VAC)
|
| 003-1498-00
| Filter for 3M Toner Vacuums
|
| 003-0619-00
| DIP IC removal tool
|
| 003-1633-00 |
PLCC IC removal tool |
| 161-0310-00 |
Power cord, US, shielded |
| 161-0066-09 |
Power cord, 220V Euro |
| 161-0066-10 |
Power cord, U.K. |
| 161-0066-11 |
Power cord, Australian |
| 161-0154-00 |
Power cord, Swiss |
| 161-0240-00 |
Power cord, Danish |
| 006-7998-00 |
Conductive grease, silicon |
| 065-0598-00 |
Shipping box, replacement kit |
| 004-5127-00 |
Shipping Carton |
<< Back to Top of Page
<< Back to Phaser 2135
Support...
|
